King Kutter King kutter Lawn Mower 999994 Manual do Utilizador

PO Box 1200 305 Commerce Drive Winfield, Alabama 35594 FREE FLOATING REAR DISCHARGE FLEX HITCH FINISHING MOWER Part No 999994 www.kingkutter.com

BEFORE PUTTING FINISHING MOWER INTO SERVICE (IMPORTANT-INSTRUCTIONS PRIOR TO START UP) SHIPPED WITH OIL IN GEARBOX SHIPPED WITHOUT GREASE IN GREASE F

SAFETY TRAINING  Safety is a primary concern in the design and manufacture of our product. Un-fortunately, our efforts to provide safe equipment

PREPARTION  Never operate the tractor and mower until you have read and completely under-stand this manual, the Tractor Operator’s Manu

OPERATIONAL SAFETY  The use of this equipment is subject to certain hazards that cannot be protected against by the mechanical means or product de

OPERATIONAL SAFETY continued...  Never allow the cutting blade to contact such items. Cut material higher at first, allowing finishing mower to

OPERATIONAL SAFETY continued...  Pass finishing mower diagonally through sharp dips and avoid sharp drops to prevent ―hanging up‖ tra

16 ATTACHING TO TRACTOR STEP 1 Attach to tractor's category 1 three point hitch as desc

17 ATTACHING TO TRACTOR continued... STEP 5 Place and hold inner PTO shaft section next to outer section and check if PTO shaft is too lon

18 SIZING PTO SHAFT STEP 1 Cutting the PTO shaft to length. NOTE: Be sure to cut equal lengths of each PTO shaft section. Cla

19 OPERATING INSTRUCTIONS This mower was designed to CUT LAWN GRASS ONLY. Use of your finish- ing mower to cut any material

20 FINISHING MOWER OPERATION STEP 1 Before each use perform the maintenance described in maintenance section (pg# 21) STEP2 Read, understand, and

21 MAINTENANCE 1). Periodically check and maintain proper gear oil level. 2). Every 8 hours, grease spindles (3), roller axle (1), wheel forks (4)

22 5-6-7 FT. FINISHING MOWER TO REPLACE BELT: STEP 1 Remove top cover. STEP 2 Release adjustment spring. STEP 3 Loosen nut on adjustment pulley t

23 Figure D Figure E

24 4 FT. FINISHING MOWER ONLY TO REPLACE BELT: STEP 1 Remove top cover. STEP 2 Loosen nut on adjustment pulley to allow for movement. (See Fig.

25 4 FT. FINISHING MOWER ONLY

26 MAINTENANCE SAFETY  Good maintenance is your responsibility. Poor maintenance is an invitation to trou-ble.  Follow good shop practices.

27 SAFETY SIGN LOCATIONS The types of safety signs and locations on the equipment are shown in the illustration below. Good safety requires that you

28 1

29 2 3

TO THE PURCHASER This manual contains valuable information about your new King Kutter Flex Hitch Rear Discharge Finishing Mower. It has been

30 4 5

31 6 7 8

32 9 10

33 11 12 MODEL NO. DESCRIPTION SN# XXXXXXXXXX

34 REAR DISCHARGE FLEX HITCH FINISHING MOWER

35 Ref. No. Part Name 4’ 5’ 6’ 7’ STAINLESS 1 Top Cover 124684 124685 124686 124687 2 Gear Box Plate 403029 403025 403025 403025 3 Idle

38 40 HP GEARBOX

39 Ref. No. Part Name 4’-5’-6’ Gearbox 184000 7’ Gearbox 184005 1 Snap Ring 106138 106138 2 Input Seal (NAK 35 x 54 x 10) 156010 156010 3 Fron

36 22" PTO 147022 Ref. No. Part Name 147022 1 Roll Pin Kit 500131 2 Male Tube End Yoke 151045 3 Implement End Yoke 151040 4 Female Tube

37 Blade Spindle Unit Ref. No. Part Name 502303 502304 1 & 2 Bearing Kit - (2) Ball Bearings (6205), (2) Seals (TCM25x52x7TC), (4) Snap Rings

It is the purchaser and/or operator’s responsibility to….  Read and understand the information contained in this manual.  Operate, lubricate,

40 BONDIOLI- (BYPY) 1). There are 3 white tabs around the cover as shown in (A in FIG. 1). Take a screwdriver and press against t

41 BONDIOLI COVER REMOVAL FIGURE- 1 FIGURE– 2 FIGURE– 3 FIGURE– 4 FIGURE– 5 EUROCARDAN SERIES 4 COVER REMOVAL LA MAGDALENA COVER REMOVAL

42 PTO SHAFTS COVER REMOVAL EUROCARDAN SERIES 5 1). There are 2 black tabs around the cover as shown in (B in FIG. 1). Take a flat screwdriver a

43 1. Limited Warranty. King Kutter, Inc. (―King Kutter‖), P.O. Box 1200, Winfield, Alabama 35594, warrants to the original retail pur-chaser (―Purcha

5 CONTENTS ITEM PAGE Safety ... 6 Assembly Instructions ...

SAFETY READ AND FOLLOW THE INSTRUC-TIONS IN THIS MANUAL AND ESPE-CIALLY IN THE SAFETY SECTION. FAILURE TO DO SO CAN RESULT IN SERIOUS IN

EQUIPMENT SAFETY GUIDELINES  Safety of the operator and by standards is one of the main concerns in designing and devel-oping a mower. However, e

FINISHING MOWER ASSEMBLY INSTRUCTIONS STEP 1 With finishing mower still in crate, lay flat on a level surface. Remove the top & s

9 Figure E Figure F Figure D Figure C